|
|
U-Boot v1.3.3 (Development build) (Build time: Dec 19 2010 - 22:03:21)
Warning: Board descriptor tuple not found in eeprom, using defaults
CN3010_EVB_HS5 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz dat
a rate)
Press any key to continue(3S)...
1
Ageing before is OK
Warning: Board descriptor tuple not found in eeprom, using defaults
CN3010_EVB_HS5 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz dat
a rate)
PHY:BCM54610
DRAM: 128 MB
No memory reserved for malloc(), heap in bootmem
Flash: 32 MB
Cold start
Ethernet Mac: 28:6e:d4:28:25:8e
Clearing DRAM...... done
Current board is EAP.
Current hw version is 0x1.
Kernel Image A Integrity is OK!
Kernel Image B Integrity is OK!
Current Bootup Image is A
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000 PCI 0xf8000000
Net: octeth0, octeth1, octeth2
current A, refcnt 1.
Un-Protected 1 sectors
Erasing Flash...
. done
Writing to Flash... done
Protected 1 sectors
0
Uncompressing 0x280000@0x300000 to 0xf00000@0x5500000
Lzmaunzip failed
EAP8523# setenv mtd_arg 'phys_mapped_flash:3456k(uboot)ro,3m(uImageA),3m(uImageB
),6784k(rootfs_data),8m(rootfsA),8m(rootfsB)'
EAP8523# setenv boot_kernel 'cp.b 0xbbf60000 300000 0x280000;lzmaunzip 0x300000
0x280000 5500000 0xf00000 ;bootoctlinux 5500000 root=/dev/mtdblock4 rootfstype=s
quashfs mtdparts=${mtd_arg} init=/etc/preinit panic=10 console=ttyS0,9600'
EAP8523# setenv serverip 192.168.255.101
EAP8523# setenv ipaddr 192.168.255.100
EAP8523# saveenv
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
. done
Writing to Flash... done
Protected 1 sectors
EAP8523# run update_rA
Interface 0 has 3 ports (RGMII)
Using octeth0 device
TFTP from server 192.168.255.101; our IP address is 192.168.255.100
Filename 'CaviumFus-squashfs'.
Load address: 0x5500000
Loading: octeth0: Up 100 Mbps Full duplex (port 0)
#
done
Bytes transferred = 512 (200 hex), 45 Kbytes/sec
protect addr:0xbcc00000,0xbd3fffff
Un-Protected 64 sectors
................................................................ done
Copy to Flash... done
protect addr:0xbcc00000,0xbd3fffff
Protected 64 sectors
EAP8523# run update_kA
Using octeth0 device
TFTP from server 192.168.255.101; our IP address is 192.168.255.100
Filename 'vmlinux.64.lzma'.
Load address: 0x5500000
Loading: #
done
Bytes transferred = 512 (200 hex), 45 Kbytes/sec
protect addr:0xbbf60000,0xbc25ffff
Un-Protected 24 sectors
........................ done
Copy to Flash... done
protect addr:0xbbf60000,0xbc25ffff
Protected 24 sectors
EAP8523# protect off bc560000 bcbfffff
protect addr:0xbc560000,0xbcbfffff
Un-Protected 53 sectors
EAP8523# erase bc560000 bcbfffff
..................................................... done
EAP8523# reset
U-Boot v1.3.3 (Development build) (Build time: Dec 19 2010 - 22:03:21)
Warning: Board descriptor tuple not found in eeprom, using defaults
CN3010_EVB_HS5 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz dat
a rate)
Press any key to continue(3S)...
1
Ageing before is OK
Warning: Board descriptor tuple not found in eeprom, using defaults
CN3010_EVB_HS5 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz dat
a rate)
PHY:BCM54610
DRAM: 128 MB
No memory reserved for malloc(), heap in bootmem
Flash: 32 MB
Soft reset counter=0
Ethernet Mac: 28:6e:d4:28:25:8e
Clearing DRAM...... done
Current board is EAP.
Current hw version is 0x1.
Kernel Image A Integrity is OK!
Kernel Image B Integrity is OK!
Current Bootup Image is A
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000 PCI 0xf8000000
Net: octeth0, octeth1, octeth2
current A, refcnt 0.
Un-Protected 1 sectors
Erasing Flash...
. done
Writing to Flash... done
Protected 1 sectors
0
Uncompressing 0x280000@0x300000 to 0xf00000@0x5500000
Lzmaunzip failed
EAP8523# DI
Start setting Bootup Indicator.....
Bootup Indicator <image-A>: A
Bootup refcnt <A>:
Un-Protected 1 sectors
Erasing Flash...
. done
Writing to Flash... done
Protected 1 sectors
EAP8523# reset
U-Boot v1.3.3 (Development build) (Build time: Dec 19 2010 - 22:03:21)
Warning: Board descriptor tuple not found in eeprom, using defaults
CN3010_EVB_HS5 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz dat
a rate)
Press any key to continue(3S)...
1
Ageing before is OK
Warning: Board descriptor tuple not found in eeprom, using defaults
CN3010_EVB_HS5 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz dat
a rate)
PHY:BCM54610
DRAM: 128 MB
No memory reserved for malloc(), heap in bootmem
Flash: 32 MB
Soft reset counter=0
Ethernet Mac: 28:6e:d4:28:25:8e
Clearing DRAM...... done
Current board is EAP.
Current hw version is 0x1.
Kernel Image A Integrity is OK!
Kernel Image B Integrity is OK!
Current Bootup Image is A
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000 PCI 0xf8000000
Net: octeth0, octeth1, octeth2
current A, refcnt 2.
Un-Protected 1 sectors
Erasing Flash...
. done
Writing to Flash... done
Protected 1 sectors
0
Uncompressing 0x280000@0x300000 to 0xf00000@0x5500000
Lzmaunzip failed
EAP8523#
|
|
发表于 2016-3-28 19:16:01
收藏
转播
分享
淘帖
支持
反对