|
|
2281开卡见红，请麻烦帮忙看看哪儿的问题，板子检查好几遍了，确实不知道是哪儿出错了
日志文件主体如下：
- Proceeding in ROM mode, download feature 3...
- FATAL_ERROR: Could not download MFB to the drive...(0x11000001:SF_SG_DEVICE_CHECK_CONDITION_ERROR)
Extended Error data:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ATA COMMAND : 0x0092 (146)
ATA FEATURE : 0x0003 (3)
Device Status: 0x0001 (1)
Driver Status: 0x0000 (0)
Host Status: 0x0008 (8)
~~~~~~~~~~~~~~
Sense Data:
~~~~~~~~~~~~~~
0 - No Sense: 114 (0x72) OK
1 - Recovered Error: 11 (0x0B) FAIL
2 - Not Ready: 0 (0x00) OK
3 - Medium Error: 0 (0x00) OK
4 - Hardware Error: 0 (0x00) OK
5 - Illegal Request: 0 (0x00) OK
6 - Unit Attention: 0 (0x00) OK
7 - Data Protect: 14 (0x0E) OK
8 - Blank Check: 9 (0x09) OK
9 - Vendor Specific: 12 (0x0C) OK
10 - Copy Aborted: 0 (0x00) OK
11 - Aborted Command: 0 (0x00) OK
12 - Equal Comparison: 0 (0x00) NA
13 - Volume Overflow: 0 (0x00) NA
14 - Miscompare: 0 (0x00) OK
15 - Reserved: 128 (0x80) NA
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
System Trace:
~~~~~~~~~~~~~~~~
[ 688.678944] ata1.00: status: { DRDY ERR }
[ 688.678948] ata1.00: error: { ABRT }
[ 688.678961] ata1.00: device reported invalid CHS sector 0
[ 688.678984] sd 0:0:0:0: [sda] START_STOP FAILED
[ 688.678987] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 688.678993] sd 0:0:0:0: [sda] Sense Key : Aborted Command [current] [descriptor]
[ 688.679001] sd 0:0:0:0: [sda] Add. Sense: No additional sense information
[ 688.679135] ata1.00: disabled
[ 693.683894] ata1: hard resetting link
[ 694.143046] ata1: softreset failed (device not ready)
[ 694.143054] ata1: applying SB600 PMP SRST workaround and retrying
[ 694.298069] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 694.299077] ata1.00: ATA-8: SandForce{200026BB}, 20DABBR0, max UDMA/133
[ 694.299085] ata1.00: 64 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 694.304758] ata1.00: configured for UDMA/133
[ 694.304772] ata1: EH complete
[ 694.304955] scsi 0:0:0:0: Direct-Access ATA SandForce{200026 20DA PQ: 0 ANSI: 5
[ 694.308391] sd 0:0:0:0: [sda] 64 512-byte logical blocks: (32.7 kB/32.0 KiB)
[ 694.308398] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 694.308477] sd 0:0:0:0: [sda] Write Protect is off
[ 694.308483] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 694.308517] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 694.308993] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 694.310006] sda: unknown partition table
[ 694.319354] sd 0:0:0:0: [sda] Attached SCSI disk
[ 710.774417] ata1.00: exception Emask 0x50 SAct 0x0 SErr 0x90a02 action 0xe frozen
[ 710.774426] ata1.00: irq_stat 0x00400000, PHY RDY changed
[ 710.774433] ata1: SError: { RecovComm Persist HostInt PHYRdyChg 10B8B }
[ 710.774440] ata1.00: failed command: DOWNLOAD MICROCODE
[ 710.774452] ata1.00: cmd 92/03:6a:00:80:01/00:00:00:00:00/00 tag 0 pio 54272 out
[ 710.774455] res 50/00:00:80:00:00/00:00:00:00:00/e0 Emask 0x50 (ATA bus error)
[ 710.774460] ata1.00: status: { DRDY }
[ 710.774470] ata1: hard resetting link
[ 711.497055] ata1: SATA link down (SStatus 0 SControl 300)
[ 716.497051] ata1: hard resetting link
[ 716.802049] ata1: SATA link down (SStatus 0 SControl 300)
[ 716.802064] ata1: limiting SATA link speed to 1.5 Gbps
[ 721.802028] ata1: hard resetting link
[ 722.107056] ata1: SATA link down (SStatus 0 SControl 310)
[ 722.107070] ata1.00: disabled
[ 722.107107] ata1: EH complete
[ 722.107119] ata1.00: detaching (SCSI 0:0:0:0)
[ 722.110462] sd 0:0:0:0: [sda] Stopping disk
[ 722.110503] sd 0:0:0:0: [sda] START_STOP FAILED
[ 722.110508] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
|
|
发表于 2016-3-29 00:15:55
收藏
转播
分享
淘帖
支持
反对
楼主