网云科技

标题: SF2281+CCME2 开卡失败求教 [打印本页]

作者: c10sf9f1 时间: 2016-3-29 09:30
标题: SF2281+CCME2 开卡失败求教

8贴，金士顿蓝色板子
选配置文件22217 错误20
[Sun 12/27/2015 21:41:09] - Searching for flashware image for configuration 22217
[Sun 12/27/2015 21:41:09] - Manifest found for configuration 22217
[Sun 12/27/2015 21:41:09] - Flashware image extracted: 22217_fw_cl_ccmlc_Intel_64Gb_JS29F16B08CCME2_2Q_2C_1D_PP_R00426_s512.vic
[Sun 12/27/2015 21:41:09] - Searching for manufacturing image for configuration 22217
[Sun 12/27/2015 21:41:09] - Manifest found for configuration 22217
[Sun 12/27/2015 21:41:09] - Manufacturing image extracted: 22217_mf_ccmlc_Intel_64Gb_JS29F16B08CCME2_2Q_2C_1D_PP_R00426_s512.vic
[Sun 12/27/2015 21:41:09] - Proceeding in ROM mode, download feature 3...
[Sun 12/27/2015 21:42:15] - FATAL_ERROR: Could not download MFB to the drive...(0x11000001:SF_SG_DEVICE_CHECK_CONDITION_ERROR)

选配置文件22173，CAME1，倒是能download MFB，不过flash test过不去
[Sun 12/27/2015 21:06:58] - Successfully received the IDENTIFY data from the drive...
[Sun 12/27/2015 21:06:58] - Validating Manufacturing Firmware Package: /home/allen/sf/mpt/FW_PPRO_5_8_2_Release.906190.release--123456/FW_PPRO_5_8_2_Release.906190.release.123456.mfp
[Sun 12/27/2015 21:07:01] - Successfully opened the package: /home/allen/sf/mpt/FW_PPRO_5_8_2_Release.906190.release--123456/FW_PPRO_5_8_2_Release.906190.release.123456.mfp
[Sun 12/27/2015 21:07:01] - file  /home/allen/sf/mpt/FW_PPRO_5_8_2_Release.906190.release--123456/22173.123456.driveconfig Loaded successfully
[Sun 12/27/2015 21:07:01] - Warning:  Unable to query diagnostics information to perform power management settings check
[Sun 12/27/2015 21:07:01] - B01 Power Management configuration request detected
[Sun 12/27/2015 21:07:01] - Successfully extracted *.DriveConfig file: /home/allen/sf/mpt/FW_PPRO_5_8_2_Release.906190.release--123456/22173.123456.driveconfig
[Sun 12/27/2015 21:07:01] - Extracted Config_ID: 1 (22173) in DriveConfig file: /home/allen/sf/mpt/FW_PPRO_5_8_2_Release.906190.release--123456/22173.123456.driveconfig
[Sun 12/27/2015 21:07:01] - Extracted SerialOutputControl: 0
[Sun 12/27/2015 21:07:01] - Searching for flashware image for configuration 22173
[Sun 12/27/2015 21:07:01] - Manifest found for configuration 22173
[Sun 12/27/2015 21:07:01] - Flashware image extracted: 22173_fw_cl_mlc_Intel_64Gb_JS29F16B08CAME1_2Q_2C_1D_PP_R00693_s512.vic
[Sun 12/27/2015 21:07:01] - Searching for manufacturing image for configuration 22173
[Sun 12/27/2015 21:07:01] - Manifest found for configuration 22173
[Sun 12/27/2015 21:07:01] - Manufacturing image extracted: 22173_mf_mlc_Intel_64Gb_JS29F16B08CAME1_2Q_2C_1D_PP_R00693_s512.vic
[Sun 12/27/2015 21:07:01] - Proceeding in ROM mode, download feature 3...
[Sun 12/27/2015 21:07:02] - Successfully downloaded MFB to the drive...
[Sun 12/27/2015 21:07:02] - Waiting (5 sec) for the drive to settle...
[Sun 12/27/2015 21:07:07] - Successfully received the IDENTIFY data from the drive...
[Sun 12/27/2015 21:07:07] - Firmware revision reported to be: '582ABBM0'.  This indicates MFB download was successful.
[Sun 12/27/2015 21:07:07] - Successfully enabled SMART capabilities...
[Sun 12/27/2015 21:07:09] - Successfully issued a diagnostic unlock...
[Sun 12/27/2015 21:07:10] - Performing the flash test of block 0 (0x0000)...
[Sun 12/27/2015 21:07:11] - Flash Test Results:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-----------------------------------------------------------------------------
Flash Test Parameters:
-----------------------------------------------------------------------------
            Block Count: 0
            Page Count: 1
               Bus Count: 2
      Chip Enabled Count: 2
               Die Count: 1
            Lane Count: 4
            Plane Count: 2
-----------------------------------------------------------------------------
Results Notes:
-----------------------
N1 - At least one page tested and passed with no bit errors.
N2 - No test data available.  Test may have aborted, or failed during the testing.
N3 - At least one page tested and had errors less than or equal to half the range of ECC correction power.
N4 - At least  one erased page tested had bit error rate greater than half the correction power.
N5 - Walking zeros test failed.
N6 - Walking ones test failed.
N7 - Block contained factory bad block markings and testing was skipped.
N8 - At least one page tested and had bit error rate greater than the correction power on plane 0.
N9 - Block in plane 0 was marked as a factory bad block.
  N10 - At least one page tested and had bit error rate greater than the correction power on plane 1.
  N11 - Block in plane 1 was marked as a factory bad block.
-----------------------------------------------------------------------------

+------+------+------+------+--------+--------------------------------------------+---------+
| Bus  | CE | Die  | Lane | Value  | Result Notes                            | Overall |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 0 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 1 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 2 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 0 | 0 | 3 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 0 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 1 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 2 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 0 | 1 | 0 | 3 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 0 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 1 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 2 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 0 | 0 | 3 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 0 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 1 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 2 | 0x0374 | N4,N5,N6,N8,N10                         | FAIL |
+------+------+------+------+--------+--------------------------------------------+---------+
| 1 | 1 | 0 | 3 | 0x0001 | N1                                        | PASS |
+------+------+------+------+--------+--------------------------------------------+---------+

-----------------------------------------------------------------------------
  Total Number of test results: 16
         Number of failures: 7
      Number of Passed with warnings: 0
   No. Passed without warnings: 9
-----------------------------------------------------------------------------
请问是焊接问题还是跳线问题？

作者: kzr9kqh 时间: 2016-3-29 09:30

我想说你有几片ic量产U盘没清空

作者: 662exi 时间: 2016-3-29 09:30

你的是金士顿啥样的板子啊 tsop周围的跳线对了吗？有用的有少的吗？

作者: 4tvaks4h 时间: 2016-3-29 09:30

同步颗粒的要求高一点，首先你要把跳线选对，其次检查焊接，最后一步你需要把板子洗干净，引脚不干净也会造成的

作者: 9ymsw1r 时间: 2016-3-29 09:30

描述:跳线
请问图上标的Ra Rb Rc位置对吗

作者: h2vz7rbz 时间: 2016-3-29 09:30

本帖最近评分记录：共条评分

回复举报

离线k1503

UID：819430注册时间2011-01-09 最后登录2016-03-28 在线时间3236小时发帖2906 搜Ta的帖子精华2 M币1733专家25 访问TA的空间加好友用道具

数码5段

发帖2906M币1733专家25粉丝60加关注发消息只看该作者 2楼发表于: 2015-12-28

有7片fail, 这个还是先查焊接吧

作者: ixl4fkor 时间: 2016-3-29 09:30

更新，之前用CAME的配置文件不过的问题是焊接原因，补焊后可以开卡成功。
CCME2配置文件依然不行，怀疑是跳线设置问题。
重新用intel 520的板子焊了一个，CCME2的配置文件能过

作者: d826z0l 时间: 2016-3-29 09:30

感觉不是焊接问题，要不怎么CCME2的下载不成功，换成CAME1的就能下载了呢

作者: cp86e5j 时间: 2016-3-29 09:30

内容金士顿板子不好折腾/质量不咋好

作者: h2vz7rbz 时间: 2016-3-29 09:30

SF的清空能力很强的，这种不是跳线问题就是焊接问题

欢迎光临网云科技 (http://www.8x6x.com/)